ACP Technologies - Mouse Pads \ Cutting Boardl Heat Press Instructions

Heat Pressing Info

12' x 15" Rectangle Cutting Board & 12" X 15" Oval Cutting Board - Glass

1) Preheat press to 400° and set to light pressure

2) Print transfer - DO NOT REVERSE THE IMAGE!

3) Place a clean sheet of plain paper on the heat press table (optional)

4) Secure transfer to the back of the cutting board with heat tape

5) Place cutting board on the press face-down – the back of the board (with the transfer) will be face-up

6) Place a plain sheet of paper on top (optional)

7) Heat time is 8 minutes (using XG8 ink is 3 minutes 45 seconds), adjusting time as necessary for best results

Please Note:

- Do not cool in water!

8' x 11" Rectangle Cutting Board & 9" X 12" Oval Cutting Board- Glass

1) Preheat press to 400° and set to light pressure
2) Print transfer - DO NOT REVERSE THE IMAGE!
3) Place a clean sheet of plain paper on the heat press table (optional)
4) Secure transfer to the back of the cutting board with heat tape
5) Place cutting board on the press face-down – the back of the board (with the transfer) will be face-up
6) Place a plain sheet of paper on top (optional)
7) Heat time is 6 minutes (using XG8 ink is 3 minutes 45 seconds), adjusting time as necessary for best results

Please Note:
- Do not cool in water!

Cheese Cutting Board - Glass

1) Preheat press to 400° and set to light pressure
2) Print transfer - DO NOT REVERSE THE IMAGE!
3) Place a clean sheet of plain paper on the heat press table (optional)
4) Secure transfer to the back of the cutting board with heat tape
5) Place cutting board on the press face-down – the back of the board (with the transfer) will be face-up
6) Place a plain sheet of paper on top (optional)
7) Heat time is 6 minutes, using XG8 ink is 3 minutes 45 seconds, 5 minutes for Ricoh, adjusting time as necessary for best results

Please Note:
- Do not cool in water!

Wine Bottle Cutting Board - Glass

1) Preheat press to 400° and set to light pressure
2) Print transfer - DO NOT REVERSE THE IMAGE!
3) Place a clean sheet of plain paper on the heat press table (optional)
4) Secure transfer to the back of the cutting board with heat tape
5) Place cutting board on the press face-down – the back of the board (with the transfer) will be face-up
6) Place a plain sheet of paper on top (optional)
7) Heat time is 6 minutes (5 minutes for Ricoh), adjusting time as necessary for best results

Please Note:
- Do not cool in water!

8" Round Cutting Board

1) Preheat press to 400° and set to light pressure
2) Print transfer - DO NOT REVERSE THE IMAGE!
3) Place a clean sheet of plain paper on the heat press table (optional)
4) Secure transfer to the back of the cutting board with heat tape
5) Place cutting board on the press face-down – the back of the board (with the transfer) will be face-up
6) Place a plain sheet of paper on top (optional)
7) Heat time is 6 minutes (using XG8 ink is 3 minutes 45 seconds), adjusting time as necessary for best results

Please Note:
- Do not cool in water!

The information contained herein is included for illustrative purposes only and, to the best of our knowledge, is accurate and reliable. ACP Technologies cannot, however, under any circumstances make any guarantee of results or assume any obligation or liability in connection with the use of this information. As ACP has no control over the use to which others may put its products, it is recommended that the products be tested to determine if suitable for a specific application and/or information is valid in a particular circumstance. Responsibility remains with owner for the design, application and proper installation of each product. Specifier and user shall determine suitability of products for a specific application and assume all responsibility in connection therewith.

	Powered by JRank Dedicated to all your Digital Decorating needs
		1.800.741.2551
		Contact Us \| View Cart